It’s amazing just how quickly a timber frame gets put up once it starts!
After the soleplates and damp proof membrane were installed yesterday, it’s only taken a day to complete the frame on the ground floor.
Next up, the beams and joists will be going in, ready for the first floor to be completed, and within a couple of week we’ll have a complete timber frame ready for roofing.
We’re lucky to be able to use our next-door plot to site the telehandler that’s lifting the panels into place, and a few ground protection mats make sure it moving around doesn’t damage the levelled ground.
The last couple of weeks have seen a flurry of work on site as the groundworks are concluded. Since the last post, the block and beam floor has been laid and grouted providing a solid surface. The outline of the ground floor has also been laid with a layer of blocks on which our timber frame will sit.
Groundworks are now complete and we have a small week-long lull while we organise site visits and bring the next few trades into the schedule.
Next week, the scaffolding will go up around the perimeter, and the week after that, our timber frame build starts in earnest! As soon as that’s up, the metal roof installation will start, and this is also when we’ll get our hands dirty to do some of our own work, like insulating the loft space.
Finally, last weekend we installed our second, time-lapse camera on site. We’ve set it up but have no way of checking the result until we take it down, which we’ll do once the external block work is complete and there’s not much else to see outside.
A couple of weeks since we last posted and things have been moving along nicely.
In that time, all the trenches were dug so that inspections for building regulations and mining could be completed. Once those were done, the concrete went in along with some reinforcing mesh.
We’ve now started on the blockwork on which the timber frame will stand. The outside edge of our foundations are now pretty much complete and some of the internal walls have started too. We’re hoping that the blockwork will be completed in the next few days, allowing the beams of the block and beam floor to be laid.
In other news, the timber frame design is now locked down and the structural steel elements have been sent off for manufacturing and the frame is scheduled to be bought on site in a few weeks’ time.
Finally, we had little luck coercing the existing camera (source of the photo above) to take regular photos for a time-lapse video at the end and so we’ve found another specialist build camera that has built-in support for time-lapse videos and runs on batteries. It doesn’t have any internet connection, however, so we’ll set it up before the frame starts being built and will probably move it inside at some point to capture the internal work. We’ll keep using the existing camera to be able to keep an eye on work from afar and take still photos on-demand.
It’s been a bit more than a month since we last posted, and a lot of that time has been taken up by architectural stuff – tweaking door placements, finishing off all the drawings and bringing together the work done by our structural engineer with the SAP (energy efficiency) calculations ready to submit to building control.
In the meantime, our groundworker has been doing his part to keep the build going by taking our ground levels down to the final finished floor levels on our plans. The level of the mud in the photo is pretty much the level the ground floor of the house will be at.
In our back garden, we’ve opted for split-levels, mostly to save on extra soil digging but also to provide some more interest. However, this does mean having a retaining wall to stop the back part of the garden collapsing. The photo shows most of the wall up (and since then, the rest has been finished off). We haven’t decided yet what the finish on the wall will be.
This is pretty much the limit of work that can be done before our architectural drawings are passed by building control and our timber frame provider has calculated what they need in terms of foundations (validating and tweaking the work done by our structural engineer).
Everything has been submitted to building control and we’re now waiting on their approval.
While all of this is happening, we’ve decided it would be a fun idea to be able to keep an eye on build progress from afar as well as taking snapshots for posterity.
Our next door neighbours have set up a pole-mounted camera for this and we decided to do something similar. So last weekend, we went to the site and got hold of a few external timbers, some screws and “postcrete” (quick-setting concrete pre-mix for these situations).
After a bit of DIY-ing, we then mounted a battery-powered external camera and a solar panel to keep it charged, and then lifted the whole thing into a hole we dug, filled it with water and postcrete and waited!
For those of you interested in this setup, it consists of four 2×3 external timbers, each about 4 metres in length. One is sandwiched between another two with about half of the length overlapping, to give an overall height of around 6 metres. The final piece is cut to fill the gap between the outer two timbers in the lower half of the contraption. The off-cut from this can then be used to form a tripod-like support for extra strength. The whole thing stands in a hole around 1 metre deep filled half-way with water and then a bag and a half of postcrete.
Once this had set (around 10-15 minutes), we then surrounded it with stones, an earth mound and tripod-like supports on two sides. It leans to one side and sways a bit in the bracing coastal wind but so far, so good!
The camera is a Reolink Go paired with a Reolink solar panel. Due to there being no electricity or wifi on site, the camera has a battery that is charged by the solar panel. It also has a SIM card using Vodafone’s V-SIM service which charges a small monthly flat-fee for unlimited data, specifically for this sort of device. We use the Reolink app to watch the camera and take snaps, and I’m currently investigating how to automate the snapshot process so we can create a time-lapse video at the end.
Work started in earnest this week on site! Finally after many months of phone calls, paperwork and emails, physical work has started with the stripping of the topsoil.
Part of the site preparation involves bringing the soil level down to where the final foundations and house will be built. The first part of this process is to strip the topsoil, which is the top 30cm or so. This then allows various surveys to take place before the rest of the soil is removed down to the final level.
The surveys we’ll be having include an archaeology survey to make sure there aren’t any relics on our site that need to be saved, and a mining survey to make sure there aren’t any seams or mine shafts that will affect our foundations.
At the same time, we’ve been working to get electricity onto the site ready for all the tools and machinery – the trenches are dug and the cable is in.
Hopefully the building regs drawings will be ready soon and we can get those approved and move onto the first real part of the house – the foundations!
Welcome to our blog! We’re Ruben and Joanna and we’re in the process of building our new house, Seaglass, in Carbis Bay, Cornwall.
We’ve started this blog to post updates on our progress, to hopefully inspire others like us to take up their own self-build challenge.
We’ll write posts regularly, each one with a photo or render, and hopefully you’ll come on a journey with us from a muddy field to a finished house.
In the meantime, feel free to take a look around the site where we’ll also write about the companies we’re using and anything else we think is generally useful. We’re also more than happy to answer questions (as far as we can) about what we’re doing and how.